Kicker Impulse ix2302 Car Amplifier *

Here is my Kicker Impulse ix2302 car amplifier.. This amplifier is seriously loud and has ample power to run any sub you wish to pair it with... This was paired with a Kicker Solo Baric L5 15" subwoofer which is also listed on here... The amplifier is in perfect working order and excellent condition.... It has never been abused and to be honest it does not need to be as it will rattle your fillings with ease... Here is some information and the specifications... Detailed Features: RCA Line Outputs:In addition to the stereo set of RCA inputs, there is a stereo set of full range line outputs. The line outputs allow you to pass a preamp level signal from this amplifier to another amplifier. This eliminates the need to use RCA splitter cords to distribute signals to two amplifiers. Speaker Level Inputs: High level input connections are included to allow use with sources that do not have RCA preamp level outputs. Built-in Electronic Crossover: Allows you to select high pass for satellite speakers, low pass for subwoofers or bypass for full range operation. Two crossover frequencies are available, 70Hz and 110 Hz, selectable for both high pass and low pass. Protection Circuits: Auto-resetting short circuit and thermal protection circuits are included to protect the amplifier from failure due to extreme conditions. Internal Circuitry: Includes MOSFET power supply and glass epoxy circuit boards. KICKEQ Bass and Treble Boost: These bass and treble controls allows you to tune your system for ideal sound quality. The KICKEQ bass boost is centered at 40Hz, and it is continuously variable from 0 to +18dB. The KICKEQ treble boost is centered at 18kHz, and it is continuously variable from 0 to +12dB. Controls: Left Side Of Amplifier: •Gain: rotary gain control that allows you to adjust the output level •Crossover Frequency Switch: allows you to select 70Hz or 110Hz •Crossover Mode Switch: allows you to choose high pass, low pass or full range •KICKEQ Level Controls: rotary controls that allow you to adjust bass and treble boost Inputs & Outputs: Left Side of Amplifier: •High Level Input: molex plug input for included harness •RCA Output: gold-plated RCA line output jacks •RCA Input: gold-plated RCA line input jacks Right Side Of Amplifier: •Speaker Outputs: gold-plated screw terminals (each terminal is 0.356" wide) •Fuses: two 40-amp fuses •12+ (power): gold-plated screw terminal (terminal is 0.519" wide) •REM (remote turn-on): gold-plated screw terminal (terminal is 0.347" wide) •GND (ground): gold-plated screw terminal (terminal is 0.519" wide) Specifications... •stereo, bridged mono, or Tri-way output •frequency response 20-20,000 Hz •230 watts RMS x 2 at 4 ohms •720 watts RMS x 1 in bridged mode •360 watts RMS x 2 at 2 ohms •speaker-level inputs •MOSFET power supply •0-18 dB bass boost centered at 40 Hz •0-12 dB treble boost centered at 18,000 Hz •18 dB/octave crossover switchable at 70 or 110 Hz •dimensions: 18-15/16"W x 2-1/2"H x 9-1/2"D DETAILED POWER HANDLING: Dynamic (Peak) Power Rating (measured at 14.4V): •Bridged Into A 4-Ohm Load: 900 watts x 1 •Per Channel Into A 2-Ohm Load: 450 watts x 2 •Per Channel Into A 4-Ohm Load: 310 watts x 2 Continuous (RMS) Power Rating (measured at 12.5V): •Bridged Into A 4-Ohm Load: 720 watts x 1 •Per Channel Into A 2-Ohm Load: 360 watts x 2 &